Mirror powder for nails №01
Mirror Powder No. 1.
Mirror Powder No. 1 can be applied in several ways. Depending on the chosen application option, the result will be different every time: from the effect of pure silver to a variety of shades.
Method 1.
1. Standardly prepare the nail plate for applying gel polish, apply Rubber Base Gel, dry for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
2.Apply Gel Polish No. 100 BW in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
3. With an eyeshadow applicator or just with your finger (ring finger), spread the mirror powder and rub into the color until a mirror shine.
4. Fix in a UV lamp for 1 minute or 15 seconds in a LED lamp.
5. Coat the design with two thin coats of Rubber Top Gel, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully process the end with a soft buff (abrasive 180 * 220). After that, seal.
6. Using a special liquid Cleanser, remove the dispersion layer. Design is ready!
Method 2.
1. Standardly prepare the nail plate for applying gel polish, apply Rubber Base Gel, dry for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
2. Apply gel polish No. 100 BW in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in a LED lamp. Remove the dispersion layer using a special liquid Cleanser.
3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.
4. Fix in a UV lamp for 1 minute or 15 seconds in a LED lamp.
5. Coat the design with two thin coats of Rubber Top Gel, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully process the end with a soft buff (abrasive 180 * 220). After that, seal.
6. Using a special liquid Cleanser, remove the dispersion layer. Design is ready!
Method 3. The effect of pure silver.
1.Standardly prepare the nail plate for applying gel polish, apply Rubber Base Gel, dry for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
2. Apply gel polish No. 30 M in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in a LED lamp. Remove the dispersion layer with a special liquid Cleanser.
3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.
4. Fix in a UV lamp for 1 minute or 15 seconds in a LED lamp.
5. Coat the design with two thin coats of Rubber Top Gel, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully process the end with a soft buff (abrasive 180 * 220). After that, seal.
6. Using a special liquid Cleanser, remove the dispersion layer. Design is ready!
Method 4. Rose-purple silver effect.
1.Standardly prepare the nail plate for applying gel polish, apply Rubber Base Gel, dry for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
2. Apply gel polish No. 40 LC in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in a LED lamp. Remove the dispersion layer with a special liquid Cleanser.
3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.
4. Fix in a UV lamp for 1 minute or 15 seconds in a LED lamp.
5. Coat the design with two thin coats of Rubber Top Gel, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in a LED lamp.
Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully process the end with a soft buff (abrasive 180 * 220). After that, seal.
6. Using a special liquid Cleanser, remove the dispersion layer. Design is ready!
Mirror Powder No. 1 can also be applied to the gel polishes of the Crystal collection, both with and without a sticky layer. Each time you will receive new shades of coating. If the nail plate is thin, we recommend strengthening it with a base gel for maximum wearability of the powder.
BEST OFFERS IN ONE CLICK
Subscribe now to be the first to know about promotions and new products and receive personal bonuses